VP92 Series Valve Stack Venturi Generators
The VP92 Series vacuum generators are solenoid controlled, designed to interface directly onto a MAC® 92 Series Sub Base. These high flow vacuum generators can be used directly in a valve stack to provide vacuum, rather than compressed air in a cylinder port. This eliminates the need for additional vacuum generators and pneumatic components within an automation system.
Need a crossover for a competitor's product? Call Vaccon for help in choosing an equivalent model. Configure / Purchase
- Valve control on the VP92 Series vacuum generator plugs directly into the sub base for easy system control
- Valve-controlled vacuum generators include an integral valve control for vacuum blow-off for rapid part release or vacuum line clean out
- The VP92 Series generators are easily installed and/or relocated via two mounting screws making a change out from a compressed air system to vacuum in only a few minutes
- The VP92 Series generators incorporate threaded venturi cartridges, allowing for instant performance adjustment changes
Need a crossover for a competitor's product? Call Vaccon for help in choosing an equivalent model. Configure / Purchase
Features & Benefits
- Direct MAC® 92 Series Sub Base interface
- High Speed integral 2-way direct acting valves
- Precise control - individual electrical connections let you control the vacuum and the blow-off duration time
- Instantaneous vacuum as needed – minimal air consumption
- Easy installation - modular design speeds installation and minimizes assembly
- Reliable – operates trouble-free:
- No moving parts to wear or clog
- No flap valves to stick open
- No maintenance
- No downtime
- Pneumatic Pick & Place Systems
- Automated Material Handling Systems
- Automated Packaging Systems Packaging - bag/box/carton folding and handling
- Interchangeable Threaded venturi cartridges - 3 different performance levels: 200M, 200H, 250M
- Miniature vacuum switches or sensor with quick disconnect for reliable part detection.
Standard Specifications
VP92 Max Series Generator Standard SpecificationsGenerator Material: | Anodized Aluminum, Buna-N (for silencer material see Silencer Page) |
Cartridge Material: | Nylon, Buna-N O-rings available in additional materials - Consult factory for availability |
Seat Material: | Vinyl |
Medium: | Filtered (50 micron) un-lubricated, non-corrosive dry gases |
Operating Temperature: | -23° to ~122°F [-5° to ~50°C] |
Operating Pressure: | 80 PSI [5.5 bar] |
VP92 Max 2-Way Valve Specifications
Valve Type: | Axial 2-Way Solenoid Valve, Normally closed |
Valve Body Material: | Brass, Aluminum, Buna-N |
Valve Operating Pressure: | Vacuum to 120 PSI [-1 to 8 bar] |
Electrical: | 24 VDC [-15% to +10% Nominal] |
Power Consumption: | 4 watts |
Response Time: | 6 milliseconds |
Cycle Rate: | 80 cycles/second |
Average Life: | 100 million cycles |
Electrical Connection: | Fixed leads, 24 AWG, 18” [457.2mm] |
LED Indicator: | Yes |
Performance Level Designations:
“M” | 0-20”Hg, [0 to 677mbar] for medium vacuum/high flow applications |
“H” | 0-28”Hg, [0 to 948mbar] for high vacuum/standard flow applications |
VP92 Max Series Operating and Installation Requirements
Vacuum Line: | 3/8” O.D. [10mm] tube, | |
Vacuum Line Filtration: | Typically vacuum filters are not required, if desired Vaccon recommends model V375F (see In-Line Filter Page) | |
Mounting Screws: | 2 M5 screws |
Dimensional Data
Dimensional data for the VP92 Max Series Venturi Vacuum Generator is presented in 2D drawings, with all critical dimensions and port thread sizes displayed. Both imperial and metric units are included.VP92 Max Series Dimensional Data
Performance Data
Performance data for the VP92 Max Series Venturi Vacuum Generator is displayed, listing air consumption, vacuum flow at various vacuum levels, and evacuation times (for 1 cu. ft. or 1 L volumes). Data is presented in tabular and graphed formats, in both imperial and metric units.Venturi Max Series Performance Data